empire gas logs won't light

While cooler air drops. You need a registered gas technician.

Echelon Ii Direct Vent Linear Gas Fireplace

With the logs on the pilot light goes out.

. Alleyne says to look for and clear out any debris between the igniter and thermocouple. No heat comes from the furnace it shut down. Jan 29 2006.

Once the pilot is lit hold the pilot valve in for 60 seconds. To turn the logs off turn the knob clockwise without depressing towards LO then pilot. Fireplaces Wood Burning and Heating Stoves Flues and Chimneys - Pilot light on gas logs wont stay lit with logs on - We have just purchased vent free gas logs.

Often times a pilot light wont turn on resulting in absolutely zero flames happening in your fireplace. Install logs according to the installation instructions. 2- Loosen inlet tap screw until you hear the air coming out of the tap until gas odor is evident.

The main burner orifice must be centered in the venturi tube for proper combustion and to prevent sooting. This is the simplest fix for when your gas fireplace wont stay on. Use an air compressor to blow inside the pilot light and the thermocouple.

Step 3 If gas is coming out of the pilot but it still wont. The pilot is a large blue flame and in contact with the new thermocouple. They were installed a week ago.

Today I had them on for five hours then suddenly the fire went out and they started beeping at me. I called the store where I bought them Offenbachers Rockville MD and they told me to disconnect the two wires from the remote. It starts a cycle and then shut down before heating house.

Gas fireplaces if. Empire Heating Cooling - Recent Questions Troubleshooting Support. Keep in mind that the instructions to reset your pilot light.

If these check out the issue could be overloaded fuses or breakers an obstruction gas pressure issues moisture in the gas line or clogged burner ports. Bad thermocouples or electric ignition can also cause a problem. Click here to send an email to our Customer Service Department.

Cant find what you want. If gas is coming out of the pilot but it still wont light the spark igniter could be the problem. Jumped the spill switch or eco switch wires and also checked them for deterioration at the valve end but they are OK.

Empire 24 Inch Flint Hill Gas Log Set With Vent Free Propane Contour Burner - Manual Safety Pilot. Gas Fireplace Wont Light FIXEDSimple Steps To Get Your Fireplace Going Again To Warm Your HomeDIY and saveMost often these easy cleaning steps ge. Still having trouble with the heater.

Next follow pilot lighting instructions to light pilot. Air In The Line If applicable first remove the protective cap screw. The gas valve is a Mertix Maxitrol GV31.

The oxypilot is a safety device built into the fireplace so that your carbon monoxide levels are kept safe and regulated. If they dont stay lit after cleaning try the air trick at least one more time. Step 1 Check the main valve to make sure the gas is turned on.

Occasionally the sensors get a spec of dust on them and it causes them to shut down. Verify the venturi tube is not bent or distorted. Only use Empire Logs specially made for this burner.

I have an Empire Comfort System furnace that sits on the floor with a thermostat on the wall. One of the biggest problems associated with gas fireplaces is related to the pilot light. When you put it back your pilot flame should be blue or blue-white in color.

Before you go too far in your attempt to solve the problem you should check to make sure your pilot light is lit. Brett Richards walks you through how to light the pilot on an Empire Comfort Systems White Mountain Hearth Vent-Free millivolt gas log fireplace system. Check your pilot light.

If the knob wont turn turn the knob to off wait 10 minutes and try again. With the logs off the pilot light will stay lit and the flame will work. Step 2 If the gas is on and the pilot hasnt been lit in several months try purging the air out of the pilot tubing To do this hold the pilot button down for about two minutes while the air bleeds out.

Oxypilot Is Blocked With Dust or Soot. Its highly unusual for the regulator in the log base to go about fifty-cents worth of. I have new RH Peterson Real Fyre gas logs.

If the fireplace pilot light is on but wont start make sure your gas valve is turned on and check the fuse or breakers. Do not alter log placement from the prescribed layout in this manual. A pilot light that doesnt glow blue is also a problem as this means it is not getting hot enough.

3- Close tap and check for gas leak. It really can be as simple as checking your pilot light and turning it on. Put the logs back into place and wait about 10 minutes before relighting them.

The pilot light goes out when you release the pilot button. Berico can also provide yearly maintenance for your gas fireplace. Call center representative at.

This allows the pilot flame to heat the thermocouple attached to the log. You dont actually need to get close to the pilot setting - about halfway between LO and pilot will be sufficient to turn the main part of the logs off while keeping the pilot lit. From Gas Control Valve 1- Turn main gas on and proceed to next step.

If youre looking for HVAC companies in Burlington that sell and service gas log fireplaces Berico is your local provider. Almost all of our brochures and manuals are available on our sites below. Call 336 273-8663 or request a quote today.

Berico can repair your existing gas fireplace or replace it with a new set of gas logs if needed.

Empire Super Stacked Wildwood Ventless Refractory Gas Log Set Woodland Direct